Home > How To > Pa Speaker Tweeter Not Working

Pa Speaker Tweeter Not Working

Contents

No, just adding photos. Aldo Raine 10-18-2009, 09:00 AM #4 curse Active Member Member since:Jul 2008 Blu-ray collection:147 Blu-ray reviews:15 it would make more sense if both where blown vs one. we got answers: To view links or images in signatures your post count must be 10 or greater. My thanks to David Kasper for allowing the link.

The best available adhesives (epoxy or polyester/ polyurethane resins) can stand actual temperatures of up to 250°C - at least in the short term. Doing so at very low volume of course. Share Quote 29th August 2013 #16 poopynuggeteer Gear Maniac My Studio Thread Starter I did this. Once tripped, a PTC takes a minute or so to self reset and this is generally not acceptable in live music applications. 2. Or stick the suspected-broken tweeter in the other speaker.

How To Test A Tweeter With A Multimeter

SO looks like somehow I blew a tweeter with this experiment. Top Tue, 2013-05-14 15:46 #15 MajorFubar Offline Last seen: 1 week 4 days ago Joined: 03/03/2010 - 00:01 Posts: 5665 RE: Tweeter not working? BYE.

  • Is this a russian letter?
  • Not sure where to start on getting this thing back going again so I figured I'd throw the pic up and see if you guys have any ideas.
  • That might have been the reason why the previous owner wanted to sell.
  • SO this is definitely some sort of capacitor issue or something with wiring.
  • I got these for $200 and even with just perfect condition woofers and tweeters that's a good deal.
  • Properly crossed-over tweeters don't need to have as high a power handling capacity as the woofers, but choose replacment tweeters with at least a 40 to 50 watt RMS power handling
  • Oturum aç Çeviri Yazısı 157.611 görüntüleme Bu videoyu beğendiniz mi?
  • You currently have 0 posts.
  • Speakers are one of those things that are robust, but hard to fix.

To be sure, it's relatively easy to burn out speakers by overdriving them with low-power amplifers, well beneath the speakers' power handing rating, which are cranked up to clipping levels (raising on the factory amp or the kenwood? Makes them pretty much useless. 11 - What then is Useful Protection? 1. Tweeter Voice Coil Replacement an inductor (coil of wire) should have a very very low ohm reading.

Some tweeters can be opened. How To Test If A Tweeter Is Blown Why do governments not execute or otherwise permanently contain super villains? Now I just hooked my iPod directly to the amp and didn't put the Mackie mxing panel in between.Again, thanks for all of your help! https://www.gearslutz.com/board/so-much-gear-so-little-time/864929-yamaha-ns-10-repair-tweeter-not-blown-just-not-working.html The big coil and the black cap are for the woofer...

Aldo Raine Blu-ray Guru Top contributor Member since:Jan 2009 Location:T.O. Blown Tweeter Or Crossover The final applied power was 38 watts and the final resistance when it cooled down measured 2.1 ohms, indicating a short had developed between the two layers. While you are looking at them, are the voltage ratings 100V or more? Ekle Bu videoyu daha sonra tekrar izlemek mi istiyorsunuz?

How To Test If A Tweeter Is Blown

Top Bartman Member Posts: 463 Joined: Fri Sep 19, 2008 11:15 am Re: How do I troubleshoot crossovers? http://www.club3g.com/forum/car-audio-electronics/141563-driver-side-door-speaker-tweeter-not-working.html We SWITCHED the crossovers and found that both tweeter and woofer of speaker B were still working (now with crossover from speaker A). How To Test A Tweeter With A Multimeter And why two black wires there... Tweeter Test Tone So, what most makers have done instead is to increase the published ratings to provide some impressive looking figures - but often with little or no reality behind them.

Still a really good deal. You never mentioned a factory amp. Besides the speakers of course, the schematic doesn't show anything else is used except the caps and the coils. Kapat Evet, kalsın. How To Repair A Tweeter

I thought there may have been a potted MOV in the mix, as an afterthought. -Harry Share Quote Loading mentioned products ... Looks fine but tests open circuit This is a nasty one as it indicates bad manufacture. Tech. I obviously have a lot to learn...Yes, passive crossovers - one in each speaker.

SoundSpeakerRepair 142.148 görüntüleme 2:31 How to fix a Blown Speaker - Süre: 3:23. Tweeter Test Songs Leo.. Share Quote 30th August 2013 #27 poopynuggeteer Gear Maniac My Studio Thread Starter Quote: Originally Posted by LeeYoo Looks like the voicecoil is cooked. Already isolated each speaker and all work fine except the driver door speakers.

Current in the wire will cause the coil to generate a force parallel to the axis of the cone; this should in turn cause the surface cone to move, thus displacing

Sounds like your problem was just speaker cones that were already worn out before you got them. Also, make sure the replacement tweeter's mounting size will work with your speakers as well. I have a theory just by looking at some of the glue spots compared to the other working box that maybe something heated up the glue enough and that caused the Tweeter Voice Coil Repair About the author: Phil Allison has worked as a pro audio designer, PA system and equipment trouble shooter and audio service tech for nearly 40 years.

It should hardly require any explanation - if you replace a smaller amp that is clipping with a bigger one that eliminates that clipping, then average power output must go up. Doesn't make sense but I wouldn't be surprised. Login / Join Join with Facebook Username I would like to join I am already a member Password Remember Me? Even one such impact can mean the end for the speaker and can result simply from a single switch on or off thump delivered from an amplifier.